1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V available
Yes, the RIVER 2 can run a Pellet Grill
Yes - RIVER 2 has enough running and surge power for the Pellet Grill. Target ~111W running / 345W surge; the generator provides 300W / 600W.
Power Margin Analysis
300W / 600W Capacity Running 189W headroom
111W required
Surge 255W headroom
345W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
PASSContinuous draw with safety buffer applied.
111W required -> 300W available (189W headroom)
Required 111W required
Available 300W
3
Surge Gate
PASSStartup peak with safety buffer applied.
345W required -> 600W available (255W headroom)
Required 345W required
Available 600W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Continuous estimate: 1.9h
Device profile reference: up to 6h per day.
Power bars show required versus available output for each gate.
View full compatibility reportDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
300W
Running Power
🔋
256Wh
Capacity
⏱️
~1.9h
Est. Runtime
☀️
110W
Solar Input
Quick Compatibility Check
- 1 Running headroom: target 111W; generator provides 300W.
- 2 Surge headroom: target 345W; generator provides 600W.
- 3 Tip: leave headroom for startup spikes and warm conditions.
Model-Specific Results
3 of 3 models are SAFE or TIGHT. Most demanding model: Traeger Legacy (Non-WiFIRE, AC motor) (300W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| Traeger Touchscreen Class (Pro 780, Ironwood 650/885) | 20W | 95W | Safe | ~9.0h | Engineering Est. |
Show expert analysisTechnical: **Running load:** ~20 W (estimated cook phase — auger motor + fan + controller after igniter shuts off). **Surge:** 95 W (igniter startup phase, first 4 minutes). Requires 120V AC output. After the igniter cycle, power drops dramatically. Field note: Current-generation Traeger grills are extremely efficient. Even a compact 300Wh power station can run a full 6-hour cook on a single charge. The 95W igniter startup is the only meaningful load. Can I run a Traeger Pro 780 on a portable power station? Yes — after the 4-minute ignition cycle (95W), the grill draws only ~20W. Most power stations handle this easily for extended cooks. | |||||
| Traeger D2 Class (WiFIRE, non-touchscreen) | 20W | 110W | Safe | ~9.0h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 20 W (cook phase — 0.17A high end of OEM range × 120V). **Surge:** 110 W (igniter startup). Requires 120V AC output. D2 Direct Drive uses DC brushless motors that are more efficient than Legacy AC motors. Field note: D2 grills sit between Legacy (300W startup) and Touchscreen (95W startup). The cooking draw is nearly identical to Touchscreen class — the difference is only in the igniter startup phase. What's the difference between D2 and Touchscreen power draw? D2 startup is 110W vs 95W for Touchscreen. After ignition, both draw approximately 10-20W during cooking. The difference is negligible for power station sizing. | |||||
| Traeger Legacy (Non-WiFIRE, AC motor) | 96W | 300W | Safe | ~1.9h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 96 W (cook phase — 0.8A high end of OEM range × 120V). **Surge:** 300 W (igniter startup, OEM published). Requires 120V AC output. Legacy AC motors draw 5-8x more than modern D2/Touchscreen grills during cooking. Field note: If you have an older non-WiFIRE Traeger, plan for 300W surge and 96W continuous. This is 5x the cooking draw of a modern Touchscreen model. A 500Wh station barely covers a 6-hour cook — a 1000Wh station is safer. Why does my old Traeger draw so much more than new models? Legacy non-WiFIRE Traegers use AC motors and a higher-wattage igniter (300W vs 95-110W). The cooking phase draws 48-96W vs 10-20W for D2/Touchscreen. Upgrading to a current model dramatically reduces power needs. | |||||
How This Pairing Performs Across Our Database
This unit ranks #2 of 33 compatible generators for this device by buffered margin (Overkill class).
How Pellet Grill Performs Across 33 Tested Generators
33 of 33 generators are SAFE+TIGHT for Pellet Grill.
33
Safe+Tight
Safe 32 (97%)
Tight 1 (3%)
Power Comparison: EcoFlow RIVER 2 vs Top Alternatives for Pellet Grill
EcoFlow RIVER 2 Safe Overkill
Current unit
Running 300W
Surge 600W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
⚡
Outdoor & RV
Pellet Grill
Outdoor BBQ Session
Select Your Model:
96W
Running
300W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 37% Utilization
111W required 300W Capacity
189W headroom
Surge/Startup Peak 57% Utilization
345W required 600W Capacity
255W headroom
Voltage Match 120V ↔ 120V ✓
Compare Similar Units
Free Tools
Station Tools
Generator Insights
The 600 W surge window can support typical compressor-based startup loads found in small refrigerators, window AC units, and sump pumps. The 256 Wh capacity limits sustained runtime, but the 2:1 surge-to-running ratio can handle brief inrush currents during motor startup events. This unit can manage intermittent high-demand appliances in portable or backup scenarios.
LFP chemistry provides stable operation across discharge cycles. The 300 W continuous rating with 600 W surge headroom allows brief high-draw events without immediate overload shutdown. Source: EcoFlow RIVER 2 User Manual v1.0 (OEM documentation).
Extend Runtime with Solar
Keep your Pellet Grill running with solar • MPPT: 11– 30V • Max: 110W
Official EcoFlow
110W Panel
1 Hour Sun =
+0.8h per sun hour
MC4 -> XT60
Full in ~3.3h Adapter required: MC4 -> XT60.
Smart Value Goal Zero
100W Panel
1 Hour Sun =
+0.7h per sun hour
Goal Zero proprietary -> XT60 adapter required
Full in ~3.7h Adapter required: Goal Zero proprietary -> XT60 adapter required.
Smart Value Jackery
100W Panel
1 Hour Sun =
+0.7h per sun hour
Jackery proprietary -> XT60 adapter required
Full in ~3.7h Adapter required: Jackery proprietary -> XT60 adapter required.
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running load: 96 W (worst case, Legacy Non-WiFIRE cook phase). Surge: 300 W (Legacy igniter startup). Voltage: 120 V AC required. Pellet grills have two distinct phases: a brief igniter startup (4-5 min, high draw) followed by hours of low-draw cooking (auger + fan only).
Expected Behavior
Estimated runtime: ~1.9h. Power draw depends heavily on controller generation. Modern Touchscreen models (Pro 780, Ironwood) draw 95W startup / ~20W cooking. Legacy Non-WiFIRE models draw 300W startup / 48-96W cooking. Most of the cook session is at the low running wattage.
Field Note
Check your Traeger's controller type before sizing a power station. A modern Touchscreen model runs all day on a 300Wh station. A Legacy Non-WiFIRE model needs 500-1000Wh for a full cook.
Frequently Asked Questions
Can the EcoFlow RIVER 2 power a Pellet Grill?
Yes. The EcoFlow RIVER 2 provides 300W running / 600W surge. The Pellet Grill needs 111W / 345W (including 15% buffer). That leaves 189W of running headroom and 255W of surge margin.
How long will the RIVER 2 run a Pellet Grill?
Approximately 1.9 hours, based on the Pellet Grill's 96W draw and the RIVER 2's 256Wh capacity (70% usable after real-world losses).
What Else Can You Run?
With 140W allocated to the Pellet Grill, the RIVER 2 still has ~4W of margin. These devices could run simultaneously:
📺
55' LED TV
80W
🌀
Box Fan (Medium)
60W
Power Tip: To get the most out of your RIVER 2, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Pellet Grill
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: ecoflow-river-2-pellet-grill 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Running worst case = Traeger Legacy Non-WiFIRE (96W cook phase, 0.8A × 120V). Surge worst case = Traeger Legacy Non-WiFIRE (300W igniter startup, OEM direct).
⚡ Generator Specs Source
OEM Verified
EcoFlow RIVER 2 User Manual v1.0
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →
Compare these models
Similar-output alternatives you can compare side by side.