1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V available
Yes, the Delta Pro can run an Electric Chainsaw (14-inch)
Yes - Delta Pro has enough running and surge power for the Electric Chainsaw (14-inch). Target ~2001W running / 6003W surge; the generator provides 3600W / 7200W.
Power Margin Analysis
3600W / 7200W Capacity Running 1599W headroom
2001W required
Surge 1197W headroom
6003W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
PASSContinuous draw with safety buffer applied.
2,001W required -> 3,600W available (1,599W headroom)
Required 2,001W required
Available 3,600W
3
Surge Gate
PASSStartup peak with safety buffer applied.
6,003W required -> 7,200W available (1,197W headroom)
Required 6,003W required
Available 7,200W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Continuous estimate: 1.4h
Device profile reference: up to 2h per day.
Power bars show required versus available output for each gate.
View full compatibility reportDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
3600W
Running Power
🔋
3600Wh
Capacity
⏱️
~1.4h
Est. Runtime
☀️
1600W
Solar Input
Quick Compatibility Check
- 1 Running headroom: target 2001W; generator provides 3600W.
- 2 Surge headroom: target 6003W; generator provides 7200W.
- 3 Tip: leave headroom for startup spikes and warm conditions.
Model-Specific Results
3 of 3 models are SAFE or TIGHT. Most demanding model: Makita UC3551A (14-inch, 14.5A, Heavy-Duty) (5,220W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| WORX WG305.1 (14-inch, 8A, Budget) | 960W | 2,880W | Safe | ~2.6h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 960W from OEM specs (8A × 120V). **Estimated startup surge:** 2880W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Compact design, auto chain tensioning, tool-free chain replacement. Field note: The WG305.1 is the best-selling electric chainsaw on Amazon US. At 8A it's the lowest-draw saw in this set and the most power-station-friendly. The estimated 2880W surge is the main compatibility factor — the 960W running load is manageable for most mid-range stations. Can a portable power station run the WORX WG305.1 chainsaw? Only if your power source can supply at least 960W continuous and approximately 2880W surge at 120V. The motor startup surge is the main challenge, not the running watts. | |||||
| Greenworks 20222 (14-inch, 10.5A) | 1,260W | 3,780W | Safe | ~2.0h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1260W from OEM specs (10.5A × 120V). **Estimated startup surge:** 3780W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. 10.5A motor provides more cutting torque than the 8A WORX for thicker branches. Field note: The Greenworks 20222 sits in the middle of this set at 10.5A. It draws 31% more than the WORX but delivers proportionally more cutting power. The estimated 3780W surge requires a power station with adequate startup capacity — stations under 4000W surge may struggle at initial trigger pull. Is the Greenworks 20222 harder to run on a power station than the WORX? Yes — 1260W versus 960W running, with an estimated 3780W versus 2880W surge. The Greenworks needs a power source with higher continuous and surge capacity. | |||||
| Makita UC3551A (14-inch, 14.5A, Heavy-Duty) | 1,740W | 5,220W | Safe | ~1.4h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1740W from OEM specs (14.5A × 120V). **Estimated startup surge:** 5220W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Heavy-duty motor at 2900 FPM chain speed, built-in soft start for smooth startups, current limiter to protect motor from burnout under overload. Field note: The UC3551A is the professional-grade corded chainsaw in this set. At 14.5A it draws 81% more than the budget WORX. Makita's built-in soft start may reduce the actual startup surge below the estimated 5220W, but no OEM starting current is published to confirm. The current limiter is a useful feature for generator use — it throttles power rather than causing a hard trip. Can a portable power station run the Makita UC3551A? Only if your power source can supply at least 1740W continuous and approximately 5220W surge at 120V. The built-in soft start may reduce actual surge below the 3x estimate, but without OEM data this cannot be confirmed. | |||||
How This Pairing Performs Across Our Database
This unit ranks #4 of 9 compatible generators for this device by buffered margin (Balanced class).
How Electric Chainsaw (14-inch) Performs Across 33 Tested Generators
9 of 33 generators are SAFE+TIGHT for Electric Chainsaw (14-inch).
9
Safe+Tight
Safe 7 (21%)
Tight 2 (6%)
Fail 24 (73%)
Power Comparison: EcoFlow Delta Pro vs Top Alternatives for Electric Chainsaw (14-inch)
EcoFlow Delta Pro Safe Balanced
Current unit
Running 3,600W
Surge 7,200W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
Power Tools
Electric Chainsaw (14-inch)
Storm Cleanup
Select Your Model:
1740W
Running
5220W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 56% Utilization
2001W required 3600W Capacity
1599W headroom
Surge/Startup Peak 83% Utilization
6003W required 7200W Capacity
1197W headroom
Voltage Match 120V ↔ 120V ✓
Startup Surge Visual
Startup Surge
Electric Chainsaw (14-inch) vs Delta Pro
Startup surge stays within the power station surge limit.
Compare Similar Units
Free Tools
Station Tools
Generator Insights
The 7200W surge capacity can support typical motor-driven appliances during startup, including air compressor motors, well pumps, and refrigeration units that demand brief high-current events. The 3600Wh capacity provides extended runtime for moderate loads, though actual performance depends on connected equipment and environmental conditions. This unit can handle typical whole-home essentials when loads are properly managed.
The Delta Pro uses LFP chemistry, a lithium iron phosphate formulation widely recognized for thermal stability in residential applications. The manufacturer provides operational guidance in their documentation, but users must follow all installation and usage instructions to minimize risk. Source: EcoFlow DELTA Pro User Manual v1.1 (manufacturer documentation).
Extend Runtime with Solar
Keep your Electric Chainsaw (14-inch) running with solar • MPPT: 11– 150V • Max: 1600W
Official EcoFlow
400W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> XT60i
Full in ~12.9h Adapter required: MC4 -> XT60i.
Smart Value Anker
400W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> XT60i
Full in ~12.9h Adapter required: MC4 -> XT60i.
Smart Value Bluetti
350W Panel
1 Hour Sun =
+0.1h per sun hour
MC4 -> XT60i
Full in ~14.7h Adapter required: MC4 -> XT60i.
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running range: 960W (8A) to 1740W (14.5A) depending on motor size. Estimated surge range: 2880W to 5220W at 3x running (motor-load multiplier — no electric chainsaw manufacturer publishes starting watts). Voltage: 120V AC for all corded models.
Expected Behavior
Estimated runtime: ~1.4h. Electric chainsaws draw near-maximum rated power during cutting and drop to near-zero between cuts. Load spikes occur when the chain engages wood, especially in hardwood or thick limbs. At 2 hours daily use (storm cleanup), energy consumption ranges from 1920 to 3480 Wh depending on model.
Field Note
Motor startup surge is the primary compatibility concern. A chainsaw that draws 960W running may need 2880W briefly when you pull the trigger. The spread between budget (8A) and professional (14.5A) models is dramatic — nearly 2x in running watts and surge. Choose the smallest saw that handles your cutting needs to maximize compatibility with your power station.
Frequently Asked Questions
Can the EcoFlow Delta Pro power an Electric Chainsaw (14-inch)?
Yes. The EcoFlow Delta Pro provides 3600W running / 7200W surge. The Electric Chainsaw (14-inch) needs 2001W / 6003W (including 15% buffer). That leaves 1599W of running headroom and 1197W of surge margin.
How long will the Delta Pro run an Electric Chainsaw (14-inch)?
Approximately 1.4 hours, based on the Electric Chainsaw (14-inch)'s 1740W draw and the Delta Pro's 3600Wh capacity (70% usable after real-world losses).
What Else Can You Run?
With 1080W allocated to the Electric Chainsaw (14-inch), the Delta Pro still has ~60W of margin. These devices could run simultaneously:
🔥
Space Heater (Eco)
750W
📺
55' LED TV
80W
💡
LED Lamp
10W
🌀
Box Fan (Medium)
60W
❄️
Medical Fridge
80W
🧊
Portable Ice Maker
100W
Power Tip: To get the most out of your Delta Pro, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Electric Chainsaw (14-inch)
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: ecoflow-delta-pro-electric-chainsaw-14inch 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Running worst case = Makita UC3551A (1740W at 14.5A). Surge worst case = Makita UC3551A (5220W). Surge estimated using 3x motor-load multiplier policy (no OEM starting watts published for any electric chainsaw in this class).
⚡ Generator Specs Source
OEM Verified
EcoFlow DELTA Pro User Manual v1.1
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →
Compare these models
Similar-output alternatives you can compare side by side.