1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V available
No — the SOLIX C800 Plus is underpowered for a Circular Saw (Corded)
Not a safe match. The generator's output falls below the Circular Saw (Corded)'s requirement.
- • Continuous power shortfall: needs 1800W (safe target ~2070W), generator provides 1200W.
- • Startup surge shortfall: needs 5400W (safe target ~6210W), generator provides 1600W.
Power Margin Analysis
1200W / 1600W Capacity Running 870W short
2070W required
Surge 4610W short
6210W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
FAILContinuous draw with safety buffer applied.
2,070W required -> 1,200W available (870W short)
Required 2,070W required
Available 1,200W
3
Surge Gate
FAILStartup peak with safety buffer applied.
6,210W required -> 1,600W available (4,610W short)
Required 6,210W required
Available 1,600W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Runtime estimate appears after running and surge gates pass.
Power bars show required versus available output for each gate.
See generators that pass nativelyDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
1200W
Running Power
🔋
768Wh
Capacity
⏱️
—
Est. Runtime
☀️
300W
Solar Input
Quick Compatibility Check
- 1 Running headroom: target 2070W; generator provides 1200W.
- 2 Surge headroom: target 6210W; generator provides 1600W.
- 3 Result: pick a higher-output unit for safe operation.
What To Do Instead
- 1 Underpowered: The Circular Saw (Corded) needs 2070W running / 6210W surge (with 15% buffer). The SOLIX C800 Plus provides 1200W / 1600W.
- 2 Safe target: Look for a power station with at least 2070W continuous and 6210W surge at 120V.
- 3 Compatible alternative: The Pecron E3600LFP (3600W / 7000W surge) clears this device's requirements.
Model-Specific Results
0 of 3 models are SAFE or TIGHT. Most demanding model: DeWalt DWE575 (7-1/4", 15A, Lightweight) (5,400W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| DeWalt DWE575 (7-1/4", 15A, Lightweight) | 1,800W | 5,400W | Fail | — | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1800W from OEM nameplate (15A × 120V). **Estimated startup surge:** 5400W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Universal motor, 5200 RPM no-load, 7-1/4" blade, 8.8 lbs. Field note: The DWE575 is the best-selling corded circular saw in the US. At 8.8 lbs it's the lightest 15A saw available, making it popular for overhead and extended jobsite use. The 5400W estimated surge means most power stations under 3000W surge capacity will struggle to start this saw under load. Can a portable power station run the DeWalt DWE575? Only if your power source can supply at least 1800W continuous and approximately 5400W surge at 120V. The motor startup surge is the main challenge — a 2000W station with only 3000W surge may trip on startup. | |||||
| Makita 5007MG (7-1/4", 15A, Magnesium) | 1,800W | 5,400W | Fail | — | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1800W from OEM nameplate (15A × 120V). **Estimated startup surge:** 5400W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Universal motor, 5800 RPM no-load, 7-1/4" blade, magnesium construction. Field note: The 5007MG's magnesium housing makes it durable and well-balanced for professional use. Its 5800 RPM is the highest in this set. From a power station perspective, it's electrically identical to the DeWalt — same 15A draw, same estimated 5400W surge. Choose between them based on ergonomics and blade speed, not electrical compatibility. Is the Makita 5007MG harder to run on a power station than the DeWalt? No — both draw 15A (1800W) with an estimated 5400W startup surge. The Makita spins faster (5800 vs 5200 RPM) but that doesn't affect the electrical load. Any power source that runs one will run the other. | |||||
| Ryobi CSB125 (7-1/4", 13A, Budget) | 1,560W | 4,680W | Fail | — | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1560W from OEM nameplate (13A × 120V). **Estimated startup surge:** 4680W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Universal motor, 5000 RPM no-load, 7-1/4" blade. Field note: The CSB125 is the most power-station-friendly circular saw in this set. At 1560W running and 4680W estimated surge, it opens up compatibility with mid-range power stations (3000W+ surge) that cannot start a 15A saw. If you're buying a corded saw specifically for portable power use, the 13A rating is a real advantage. Why choose the Ryobi 13A over a 15A saw for portable power? The 13A Ryobi draws 1560W running and an estimated 4680W surge — 13% less than 15A saws. This difference can mean the difference between a power station starting the saw or tripping on overload. | |||||
How This Pairing Performs Across Our Database
This unit is outside the compatible set; 9 of 33 generators pass SAFE/TIGHT for this device.
How Circular Saw (Corded) Performs Across 33 Tested Generators
9 of 33 generators are SAFE+TIGHT for Circular Saw (Corded).
9
Safe+Tight
Safe 7 (21%)
Tight 2 (6%)
Fail 24 (73%)
Power Comparison: Anker SOLIX C800 Plus vs Top Alternatives for Circular Saw (Corded)
Anker SOLIX C800 Plus Fail
Current unit
Running 1,200W
Surge 1,600W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
⚡
Power Tools
Circular Saw (Corded)
Job Site Power
Select Your Model:
1800W
Running
5400W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 173% Utilization
2070W required 1200W Capacity
870W short
Surge/Startup Peak 388% Utilization
6210W required 1600W Capacity
4610W short
Voltage Match 120V ↔ 120V ✓
Startup Surge Visual
Startup Surge
Circular Saw (Corded) vs SOLIX C800 Plus
Startup surge exceeds the power station limit. A soft starter may resolve the surge gap.
⚠️
Before You Buy: Connection Check
Amperage check
This load may exceed a standard 15A outlet. Verify your station has a higher-amperage outlet (20A/30A) before purchase.
Compatible Alternatives to SOLIX C800 Plus
These generators meet Circular Saw (Corded)'s voltage, running, and surge requirements.
Best Value 
Pecron E3600LFP
3600W • 3072Wh
Runtime at your load
~1.2h
Capacity Fit Expandable to 15360Wh
Lowest capacity that still clears surge + running load.
Max Runtime 
Delta Pro
3600W • 3600Wh
Runtime at your load
~1.4h
Longest Runtime Expandable to 25000Wh
Expandable to 25000Wh.
Compare Similar Units
Free Tools
Station Tools
Generator Insights
The 1600W surge rating can support startup sequences for refrigerator compressors, well pumps, and similar inductive motor loads that draw 25 to 33 percent over running current during initial engagement. Once running, the 1200W continuous output can handle typical kitchen appliances, electronics, and power tools within rated limits. This combination addresses both inrush events and sustained runtime needs in backup scenarios.
This unit uses LFP chemistry, a battery architecture chosen for thermal stability in consumer power stations. The 768Wh capacity and 1200W continuous output allow sustained operation without thermal stress under typical residential loads. Source: Anker SOLIX C800 Plus Tech Specs (manufacturer documentation).
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running range: 1560W (13A) to 1800W (15A) depending on motor rating. Estimated surge range: 4680W to 5400W at 3x running (motor-load multiplier — no circular saw manufacturer publishes starting watts). Voltage: 120V AC for all corded models.
Expected Behavior
Circular saws draw near-maximum rated power during cutting and drop to near-zero between cuts. Unlike compressors or refrigerators, there is no continuous cycling — the load is entirely user-controlled. At 1 hour daily use, energy consumption ranges from 1560 to 1800 Wh depending on model.
Field Note
Startup surge is the primary compatibility bottleneck, not running watts. A circular saw motor must overcome blade inertia from standstill, creating a brief 3x inrush event. Blade binding in wood can also spike current above rated amps — size your power source for the surge rating, not the nameplate amps.
Frequently Asked Questions
Can the Anker SOLIX C800 Plus power a Circular Saw (Corded)?
No. The Anker SOLIX C800 Plus falls short on both running (1200W offered vs 2070W needed) and surge (1600W offered vs 6210W needed). Safe targets include a 15% buffer for the Circular Saw (Corded)'s motor load profile.
How long will the SOLIX C800 Plus run a Circular Saw (Corded)?
No reliable runtime estimate — this pairing is not compatible. The Anker SOLIX C800 Plus cannot safely power the Circular Saw (Corded). See compatible alternatives above for power stations that meet this device's requirements.
Power Tip: To get the most out of your SOLIX C800 Plus, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Circular Saw (Corded)
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: anker-solix-c800-plus-circular-saw-corded 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Running worst case = DeWalt DWE575 / Makita 5007MG (1800W at 15A). Surge worst case = DeWalt DWE575 / Makita 5007MG (5400W). Surge estimated using 3x motor-load multiplier policy (no OEM starting watts published for any circular saw in this class).
⚡ Generator Specs Source
OEM Verified
Anker SOLIX C800 Plus User Manual (EN-US)
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →