1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V available
No — the SOLIX C300 is underpowered for a Gas Furnace Fan (Blower)
No - this pairing is underpowered. Safe target ~1217W running / 2795W surge; the generator provides 300W / 300W.
- • Continuous power shortfall: needs 1058W (safe target ~1217W), generator provides 300W.
- • Startup surge shortfall: needs 2430W (safe target ~2795W), generator provides 300W.
Power Margin Analysis
300W / 300W Capacity Running 917W short
1217W required
Surge 2495W short
2795W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
FAILContinuous draw with safety buffer applied.
1,217W required -> 300W available (917W short)
Required 1,217W required
Available 300W
3
Surge Gate
FAILStartup peak with safety buffer applied.
2,795W required -> 300W available (2,495W short)
Required 2,795W required
Available 300W
3b
With Soft-Start
FAILAlternative startup path with reduced inrush.
1,258W required -> 300W available (958W short)
Required 1,258W
Available 300W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Runtime estimate appears after running and surge gates pass.
Power bars show required versus available output for each gate.
See generators that pass nativelyDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
300W
Running Power
🔋
288Wh
Capacity
⏱️
—
Est. Runtime
☀️
100W
Solar Input
Quick Compatibility Check
- 1 Running headroom: target 1217W; generator provides 300W.
- 2 Surge headroom: target 2795W; generator provides 300W.
- 3 Result: pick a higher-output unit for safe operation.
What To Do Instead
- 1 Underpowered: The Gas Furnace Fan (Blower) needs 1217W running / 2795W surge (with 15% buffer). The SOLIX C300 provides 300W / 300W.
- 2 Safe target: Look for a power station with at least 1217W continuous and 2795W surge at 120V.
- 3 Compatible alternative: The VTOMAN Jump 1500X (1500W / 3000W surge) clears this device's requirements.
Model-Specific Results
0 of 3 models are SAFE or TIGHT. Most demanding model: Goodman GMH8 0805B (80,000 BTU) (2,430W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| Carrier Infinity 59MN7A 080 (80,000 BTU) | 886W | 1,461W | Fail | — | OEM Manual |
Show expert analysisTechnical: **Running load:** 886W (115V × 7.7A FLA, OEM rated). **Surge:** 1,461W (115V × 12.7A start amps, OEM rated). **Voltage:** 120V AC. The ECM variable speed blower ramps up electronically with a controlled startup — the 1,461W surge is brief and predictable. Field note: The Carrier Infinity is the most generator-friendly furnace blower in this comparison. The ECM variable speed motor keeps both running and surge watts low. Most power stations above 1,500W can handle this unit without issue. Can I run a Carrier Infinity furnace on a portable power station during a winter outage? Only if your power source can supply at least 886W continuous and 1,461W surge at 120V. The ECM variable speed blower has a controlled startup that most mid-size power stations can handle. | |||||
| Trane S8X1 B080 (80,000 BTU) | 1,058W | 1,587W | Fail | — | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1,058W (115V × 9.2A FLA, OEM rated). **Surge:** 1,587W estimated (1.5× for ECM constant torque motor — OEM start amps not published). **Voltage:** 120V AC. The 3/4 HP constant torque ECM blower draws more than the Carrier variable speed but still benefits from electronic startup control. Field note: The Trane S8X1 is a mid-range 80% AFUE furnace common in existing homes. The 9-speed ECM blower is more efficient than old PSC motors but draws more than premium variable speed models. A 2,000W power station provides adequate headroom. Can I keep my Trane furnace running on battery backup during a winter storm? Only if your power source can supply at least 1,058W continuous and 1,587W surge at 120V. The ECM blower has a moderate startup demand that most 2,000W+ power stations can handle. | |||||
| Goodman GMH8 0805B (80,000 BTU) | 810W | 2,430W | Fail | — | NEC Standard |
Show expert analysisTechnical: **Running load:** 810W (derived from OEM Min Circuit Ampacity 8.8A de-rated by NEC 1.25× factor). **Surge:** 2,430W (3× running per NEC for PSC induction motor — OEM LRA not published). **Voltage:** 120V AC. The 4-speed PSC motor creates a hard mechanical inrush on every startup — three times the running load. Field note: The Goodman GMH8 represents millions of builder-grade furnaces installed across the US. The PSC motor surge is the critical factor — running watts are actually lower than ECM models, but the 2,430W startup spike will trip any power station under 2,500W. This is the #1 reason furnace blowers fail on small generators. Why does my power station shut off when the Goodman furnace blower starts? Because the PSC blower motor creates a 2,430W startup surge — 3× its 810W running draw. Most power stations under 2,500W surge capacity will trip on this inrush. You need a station rated for at least 2,430W surge to handle it reliably. | |||||
How This Pairing Performs Across Our Database
This unit is outside the compatible set; 22 of 33 generators pass SAFE/TIGHT for this device.
How Gas Furnace Fan (Blower) Performs Across 33 Tested Generators
22 of 33 generators are SAFE+TIGHT for Gas Furnace Fan (Blower).
22
Safe+Tight
Safe 20 (61%)
Tight 2 (6%)
Soft Start 1 (3%)
Fail 10 (30%)
Power Comparison: Anker SOLIX C300 vs Top Alternatives for Gas Furnace Fan (Blower)
Anker SOLIX C300 Fail
Current unit
Running 300W
Surge 300W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
Heating & Cooling
Gas Furnace Fan (Blower)
Winter Heating Emergency
Select Your Model:
1058W
Running
2430W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 406% Utilization
1217W required 300W Capacity
917W short
Surge/Startup Peak 932% Utilization
2795W required 300W Capacity
2495W short
Voltage Match 120V ↔ 120V ✓
Startup Surge Visual
Startup Surge
Gas Furnace Fan (Blower) vs SOLIX C300
Startup surge exceeds the power station limit. A soft starter may resolve the surge gap.
⚠️
Before You Buy: Connection Check
Installation warning
These systems are often hardwired to a home panel. To run them from a portable station, you may need a transfer switch installed by an electrician. You cannot just plug it in.
Compatible Alternatives to SOLIX C300
These generators meet Gas Furnace Fan (Blower)'s voltage, running, and surge requirements.
Best Value 
VTOMAN Jump 1500X
1500W • 828Wh
Runtime at your load
~0.5h
Capacity Fit Expandable to 2376Wh
Lowest capacity that still clears surge + running load.
Max Runtime 
Delta Pro
3600W • 3600Wh
Runtime at your load
~2.4h
Longest Runtime Expandable to 25000Wh
Expandable to 25000Wh.
Compare Similar Units
Free Tools
Station Tools
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running load: 810–1,058W depending on motor type (ECM vs PSC). Surge: 1,461–2,430W. Voltage: 120V AC required. The motor technology — ECM variable speed, ECM constant torque, or PSC multi-speed — determines both the running draw and the startup surge that your power station must handle.
Expected Behavior
Gas furnace blowers run 8+ hours per day during winter emergencies. ECM motors (Carrier, Trane) have controlled electronic startup. PSC motors (Goodman) create hard mechanical inrush at 3× running watts on every heating cycle. Daily energy ranges from 6,480–8,464 Wh.
Field Note
The blower motor is the only significant electrical load in a gas furnace — the gas burner itself uses negligible electricity. Check your furnace nameplate for motor type: ECM or constant torque means manageable surge; PSC or multi-speed means you need a power station rated for at least 2,500W surge.
Frequently Asked Questions
Can the Anker SOLIX C300 power a Gas Furnace Fan (Blower)?
No. The Anker SOLIX C300 falls short on both running (300W offered vs 1217W needed) and surge (300W offered vs 2795W needed). Safe targets include a 15% buffer for the Gas Furnace Fan (Blower)'s motor load profile.
How long will the SOLIX C300 run a Gas Furnace Fan (Blower)?
No reliable runtime estimate — this pairing is not compatible. The Anker SOLIX C300 cannot safely power the Gas Furnace Fan (Blower). See compatible alternatives above for power stations that meet this device's requirements.
Power Tip: To get the most out of your SOLIX C300, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Gas Furnace Fan (Blower)
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: anker-solix-c300-gas-furnace-blower 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Worst case running = Trane S8X1 B080 (1058W). Worst case surge = Goodman GMH8 080 (2430W). Running and surge maxima come from different variants due to ECM vs PSC motor technology.
⚡ Generator Specs Source
OEM Verified
Anker SOLIX C300 User Manual (EN-US)
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →